Categories: Framing

Selecting TJI Floor Joist Sizes

Using TJI Span Tables

The following screen shot comes from the Trus Joist TJI Manual. It shows the standard span tables for TJI’s. The tables look overwhelming but they are actually pretty simple to use. They are organized by two main tables, one for live load deflections of L/360 and one for L/480. Within each of those two tables the information is divided again into to sections, one section for a dead load of 10 pounds per square foot (psf) and one for 20 psf.

So the question is: How on earth do I use these tables? Minimum codes typically require a live load of 40 psf and a dead load of 10 psf. These minimum design loads work well as a minimum safe loading capacity. However, those actually loads don’t typically govern the design. The minimum deflection criteria of L/360 will usually control.

L/360 means that if you have a joist spanning 10 feet you can expect it to deflect 0.33 inches at mid-span based on 40 psf live loading. I don’t know about you but a deflection of almost 3/8 of an inch while I’m walking across the floor seems too “bouncy”. That’s why the tables are also written for L/480. For the same 10 foot span you can then expect a deflection of 1/4 inch.

So my recommendation is to select your floor joists based on L/480 deflection criteria. Now depending on the room you’ll need to decide if you want to account for 10 psf dead loading or the higher 20 psf. Again for my house I went with the higher dead load of 20 psf because I wanted a really nice stiff floor that wouldn’t “bounce” as we walked around.

Page: 1 2 3

Todd Fratzel

I'm full time builder for a large construction company in New Hampshire. I run their design-build division that specializes in custom homes, commercial design-build projects and sub-divisions. I'm also a licensed civil and structural engineer with extensive experience in civil and structural design and home construction. My hope is that I can share my experience in the home construction, home improvement and home renovation profession with other builders and home owners. I'm also the Editor-in-Chief and Founder of Tool Box Buzz. Please feel free to contact me if you have any questions, suggestions or you'd like to inquire about advertising on this site.

View Comments

  • how do you attach to concrete stem wall. it would be helpfull to have a picture for the want to build your own home person.i will soon be using this product.

    • Alan - Can you be more specific? Are you hanging the joists from the face of the wall or will the joists be sitting on top of the wall?

  • So, I am remodeling a garage (20' ceiling) to add a second floor. My plan is to lag bolt 2x12's to the existing studs in the walls and run TJI in hangers across the span. Is this ok? Anything I should be looking at?

    • Mark - You need to be sure you have proper bearing. Quite often you need more than 1-1/2" of bearing.

  • I have a 24'x 24' gabel roof garage with loft for storage. loft is made from 2"x 8" joist spaning across 24', 24"oc with 1/2" plywood floor. Rafters are 2"x 6" 24" oc, set on 2"x 8" ridge board, notched on to walls. the roof has 7-12 pitch. the joist sit on top of 2"x 4" walls nailed to rafters. Walls are 8' made of 2"x4" 16"oc with double top plate. I would like to use the loft as a lounge possably adding a dormer on one side of the roof. What can I do to stengthen the joist and floor. I have thougth of sistering 2"x10" to the 2"x8" and adding one between ea. to make it 12"oc. Would this be enough. I've been told also to attach 2"x4" to the joist and raffters about 6' in, but that would kill the dormer. Could i just do it on one side and leave the other side open.

    • Is there a center support in the middle of the 24' span? If not you'll be hard pressed to span 24' without using some serious TJI's. You'd likely be better off removing the old joints one at a time and replacing with a properly sized TJI. However, the depth of them will be a concern. you may need to create a ledger and drop them down which ultimately drops your garage ceiling height down.

      Any photos?

  • No center support. There is four to five inches clearance over the top of the overhead door. The ledger (to the wall?),sounds like it would work, how would I attach it, and what dimension. I have photos. I've subscribed via e-mail.

    • First off let me say you really need to work with a local building supplier or structural engineer to select the proper joist. Without knowing you entire situation and local building code requirements I can not give you a final solution.

      However, just for talking purposes, if you look at the table you will see that you'll need something like a TJI 230, 14" deep, spaced at 12 inches on center. So then the challenge becomes how do you get them in place without the roof falling down! Honestly you'd be better off with a center column/beam arrangement.

  • My first floor is made up of 2x10 joist's, that are 13' long. The floor has some bounce in it, and I was hoping to eliminate some, if not all, of the bounce. One idea would be to glue and screw some 3/4" plywood to every other joist, and then, add bracing every 4". What do you think?

    Thank You

    • That approach will definitely stiffen the floor. I'd install the plywood on every joist but just do the middle 8' of the joists. This is where bending stresses are highest. Bridging will also help out quite a bit. This helps engage more than one joist when a load is applied to it.

      Good luck.

      • Todd,

        Thank you for the reply.

        Should I just add the plywood to one side of the joist, or both? Should I jack the joist, before screwing and gluing the plywood? What type of plywood should I be using?

        Thank You

        • From your description it should like you're trying to fix "bouncing" of the floor. This is due to what we refer to as live load. So no jacking is required. Me personally I'd add plywood to both sides to keep things symetrical. I'd use 1/2" thick CDX plywood.

          • When adding the plywood, to both sides of every other joist, should I just glue and screw both pieces to the middle of the joist, or should I stagger the pieces, on each side of the joist? Should I still add the plywood to every other joist? Do you think 3' is a good space, for the bridging, or should it be more or less?

          • I would do every joist so the floor has an even distribution of stiffness. Not sure what you mean by staggering, I'd just use an 8' long piece at mid-span, both sides of the web.

            3' is more than enough, 4' spacing willl likely work well as well.

      • The strongest option is 1 or maybe 2 rows of bridge blocking. A 9 1/8" plywood strip, even on both sides will not stiffen enough to stop live load deflection at length.

  • Hi Todd,
    First off, thanks for putting this website together! Very helpful.
    I am a home designer and have a question about TJI sizes/ spacing vs. cost. In your experience, is it less expensive to go with a tighter spacing with a lighter joist, or wider spacing with a heavier joist?
    Regards, Larry

    • Typically the best solution is one that uses 16" o.c. spacing. That spacing works well with 3/4" sub-floors and finished flooring and it requires less labor than a 12" o.c. spacing. Obviously there are times when that won't work but that's typically my preference.

  • I would like to confirm what floor joist will yield a strong floor. I will be 24 foot outside to outside of 2x6 exterior walls of a 42 foot long home and want to keep the first floor open by using TJI joists running right to left. I will have a 12/12 pitch roof so when I get upstairs there will be a vertical wall from center outwards, at 6 foot running from front to back and supporting a stick framed 2x8 rafter...or a 12 foot room the length of the house...so the load from the roof will essentially bear at 6 foot from the downstairs exterior walls inward if I am giving a proper mental image. I am in upstate NY and want the most rigid floor I can get within reason. I don't want my daughter running back and forth and watching the floor/ceiling move before my eyes. I like to think of this as a heavy duty request/inquiry.

    • Earl - With a configuration like that you'll need to confirm sizing with a TJI rep. Most distributors have staff that are trained to use their design software and confirm sizing. Taking a quick look at the charts you're going to need a 14" or 16" deep joist. Spacing and model will depend on how much loading that upper wall framing adds to the span.

      The deeper 14" or 16" joists will need to be accounted for in floor to floor heights for stair design and details.

  • Hi I have TJI 560 series 16 inch and 16oc spanning 21 ft I have a 16 inch rim boards. Do I need squash or web fillers at the top plates at the load ends. My tji are all cut tight to the rim board If I need them how would you apply in place. Glue then screw .this is for a second floor floor joist
    Thanks

    • Frank - You'd have to look at their standard details. Typically we only see squash blocks at interior load bearing locations but it's certainly possible. Installing them wouldn't be a big deal, typically a vertical 2x4 on each side of the flange, tight to the plate below and tight to the sub-floor above would be used.

  • Todd,
    I am looking at a cantilevered radius on the second floor. The projection at the widest point is about 36". I am familiar with a doubled LVL at 1 1/2 times the cantilevered length inside the wall. I will turn the LVL beam at a 45 degree angle to the corner where the radius projects. Should I use LVL's as floor joists? It doesn't appear that a 14" TGI will support the span.
    Craig

Share
Published by
Todd Fratzel

Recent Posts

How To Build Floating Bar Shelves

Floating Walnut Bar Shelves Floating shelves are extremely popular and it's not a surprise due…

3 years ago

Custom Curved Deck with Cable Railings and Stone Grill

Custom Deck Project Building a regular deck is something we do a lot of but…

3 years ago

Stick Framed – Prefabricated – Modular – Which Is Best?

New Home Construction Options: Stick Framed, Prefabricated & Modular So you're considering building a new…

3 years ago

Why Use Pre-cut Studs for Framing Walls

Using Pre-Cut Studs To Frame Walls For those that do not frame houses on a…

5 years ago

How To Replace Taco 0014-F1 Circulator Pump Cartridge

Replacing Taco 0014-F1 Cartridge I like to try and fix things myself when they are…

5 years ago

PVC Flue Gas Venting Pipe

System 1738 - Engineered PVC Flue Gas Pipe Years ago we started installing gas boilers…

5 years ago